Build Right Kitchens | Floors | Contractors

Custom Kitchen Cabinets, Refacing and Refinishing in Bluffdale, UT

Custom Cabinets

Build Right Kitchens designs, builds and installs cabinetry from our shop in Bluffdale, Utah. Custom and semi-custom kitchen cabinets, plus refacing, refinishing and painting where the existing boxes are worth keeping. One team measures, builds and fits, so there is nobody to point at if a door does not line up.

Custom Cabinets

Custom Cabinets and Cabinet Installation in Bluffdale, UT

Custom cabinets are built to the exact dimensions of your room rather than assembled from standard sizes. That means no filler panels in visible places, full use of awkward corners, and runs that finish cleanly against an out-of-square wall. Build Right Kitchens has built and fitted them across the Salt Lake Valley since 2008.
Design, build and installation all happen in-house. Most cabinet complaints come from the gap between a supplier and a separate fitter: boxes ordered to the wrong dimensions, doors that will not align because the wall is out of plumb, filler panels improvised on the day. We measure, build and fit, so that gap does not exist. Cabinetry usually runs alongside a kitchen remodel and new countertops, and all three come from the same contract.
Not every kitchen needs new cabinets. If the boxes are sound, refacing or refinishing gets you a different kitchen for a fraction of the cost. We open a cabinet at the survey, look at the carcass rather than the door, and tell you which route actually makes sense before anything is priced.

New Cabinets, Semi-Custom, Refacing or Refinishing

There are four ways to change the cabinets in a kitchen, and they differ by a factor of ten in cost. The right one depends on the condition of the boxes and whether the layout is part of the problem.

Custom Cabinets Built to Your Kitchen

Built to your exact dimensions in any style and any finish. Worth it when standard sizes would leave filler panels on show, when a ceiling is unusually high, or when a corner would otherwise be dead space. Four to eight weeks from approved design to installation.

Semi-Custom Cabinets

Manufacturer standard sizes with your choice of door style and finish, modified in depth or width where the room needs it. The sensible choice for a kitchen keeping its existing footprint, and roughly a third of the cost of fully custom.

Cabinet Refacing

New doors, drawer fronts and hardware, with matching veneer over the boxes you already have. The style changes completely and the kitchen stays usable throughout. Only works where the carcasses are solid, square and still firmly fixed to the wall.

Cabinet Refinishing and Painting

Keep the doors and change the colour. Refinishing strips solid wood back and restains it so the grain stays visible. Painting covers the grain in a new colour. Both are the cheapest meaningful change a kitchen can have, and both are finished in days rather than weeks.

What Custom Kitchen Cabinets Cost in the Salt Lake Valley

Cabinets are priced by the linear foot, which is the length of wall the runs occupy rather than the floor area of the room. A standard kitchen is 25 to 30 linear feet. That single measure is why two kitchens that look similar can be eleven thousand pounds apart: a galley with two long runs costs less than an L-shape with an island, before anyone has chosen a door style. The table below gives typical Salt Lake Valley ranges for all five routes.

What Kitchen Cabinets Cost in the Salt Lake Valley

Typical market ranges for 2026, priced per linear foot of cabinet run and for a standard 25 to 30 foot kitchen. These are not Build Right prices. Your written estimate comes from the free in-home survey.

RoutePer linear footTypical kitchenLead timeInstall time
Cabinet painting$90 – $200$2,500 – $6,0001–2 weeksOn site throughout
Cabinet refinishing$140 – $280$3,500 – $8,0002–3 weeks2–3 days
Cabinet refacing$150 – $450$4,000 – $13,0002–4 weeks3–4 days
Semi-custom cabinets$150 – $650$5,000 – $19,0004–6 weeks3–5 days
Custom cabinets$500 – $1,200$15,000 – $35,0004–8 weeks3–5 days

Cabinetry is normally the largest single line in a kitchen budget, around 30 to 40 percent of the total. It is also the longest lead item, which is why it is ordered first and the rest of the schedule is built backwards from its delivery date. Interior fittings such as pantry pull-outs, drawer organisers and corner solutions are priced separately.

Cabinetry is normally the largest single line in a kitchen budget and always the longest lead item, so it gets ordered first and the rest of the schedule is built backwards from its delivery date. If the number sits above where you want to be this year, remodel financing offers 0% APR for up to 18 months with approval usually in days. Doing cabinets and countertops together is also cheaper than a year apart, because the templating happens once against finished cabinetry rather than twice.

Cabinet Refacing

Cabinet Refacing in Bluffdale

Cabinet refacing replaces the doors, drawer fronts and hardware and covers the visible box surfaces with matching veneer, leaving the carcasses and the layout exactly where they are. The kitchen changes style completely. The plumbing, the countertops and the backsplash never get touched.
It costs roughly a third of new cabinetry and takes two to four weeks rather than eight. It also leaves the kitchen usable for most of that, because the boxes stay in place and only the doors come off. For a kitchen with sound construction and dated styling, it is usually the better spend by a clear margin.

The limit is the boxes. Particleboard that has swollen under a sink leak, shelves that sag, or carcasses that have worked loose from the wall will not hold new doors any better than they hold the old ones. Refacing also cannot fix a layout. If the kitchen fights you every time you cook, new cabinetry is the honest answer and we will say so.

Refinishing and Painting

Cabinet Refinishing and Kitchen Cabinet Painting

Refinishing and painting both keep your doors and change what they look like. Refinishing strips the old finish back to bare wood and applies new stain or lacquer, so the grain stays visible. Painting covers the grain entirely in a new colour. Refinishing only works on solid wood. Painting works on almost anything.
Doors and drawer fronts come off and go to the shop, where they are sprayed in a controlled environment rather than brushed in your kitchen. That is the difference between a finish that still looks right in five years and one that shows every brush mark by the second summer. Frames are done on site with the room masked off.

Painted kitchen cabinets have been the most requested finish for a decade and show no sign of changing. White and off-white dominate, but deep greens, navies and warm greys all hold up well against Utah light, which is harsher and more direct than most of the country. Two-tone kitchens, with painted uppers over a stained or darker base, split the difference and are covered in the next section.

Refacing, Refinishing, Painting or New Cabinets

The four routes do different jobs and cost very different amounts. This is the decision that shapes a kitchen budget more than any other, and it is usually made before anyone has explained the difference.

OptionWhat changesWhat staysTypical costChoose it when
PaintingColour only. Grain is coveredBoxes, doors, drawers, hardware, layout$2,500 – $6,000The doors are sound and you only want a different colour
RefinishingStain or lacquer. Grain stays visibleBoxes, doors, drawers, layout$3,500 – $8,000The doors are solid wood and worth keeping on show
RefacingDoors, drawer fronts, hardware, visible surfacesBoxes and layout$4,000 – $13,000The boxes are solid but the doors are dated or damaged
Semi-custom cabinetsEverything except the footprintWhere the runs sit in the room$5,000 – $19,000You want new cabinets without moving anything
Custom cabinetsEverything, including sizes and layoutNothing has to$15,000 – $35,000The layout is wrong, or the room has awkward dimensions

Two things rule out the first three routes regardless of budget. If the layout itself is the problem, no amount of refinishing fixes it. And if the boxes are particleboard that has swollen under a leak or shelves that sag, a new face on a failing carcass buys a few years at most. We open a cabinet at the survey and tell you which group yours falls into.

Shaker, White Oak and Two-Tone Kitchen Cabinet Design

Door style sets the character of a kitchen more than the colour does, and it is the one decision that is genuinely hard to change later. Here is what we build most and what each one is actually good at.

Shaker Cabinets

A five-piece door with a flat recessed centre panel and a plain square frame. Roughly two hundred years old and in continuous use that whole time, which is the strongest argument any kitchen style has against dating. Takes paint and stain equally well, suits traditional and modern rooms, and has nowhere for grease to collect.

White Oak Cabinets

Open-grained, pale and warm, with enough texture to carry a kitchen without a second material. White oak has replaced walnut as the wood people ask for by name, and it holds up well in Utah's dry air because quarter-sawn boards move less than most species through a winter.

Two-Tone Kitchen Cabinets

Painted uppers over a stained or darker base, or an island in a contrasting colour. It breaks up a long run visually and lets a kitchen carry a strong colour without the room closing in. The usual mistake is choosing both tones separately rather than as a pair.

Painted Kitchen Cabinets

The most requested finish for a decade. Whites and off-whites dominate, though deep greens, navies and warm greys all hold up well against direct Utah light. Sprayed in the shop rather than brushed on site, which is what separates a finish that lasts from one that shows every mark.

High-End and Luxury Kitchen Cabinets

Inset doors fitted flush within the frame, hardwood dovetailed drawer boxes, integrated appliance panels and bespoke interior fittings. Tolerances are far tighter than on overlay doors, which is where the extra cost actually goes rather than into the material itself.

Soft-Close Hardware and Interior Fittings

Soft-close hinges and full-extension runners fitted as standard on everything we build, including refaced cabinets that never had them. Pantry pull-outs, deep drawer banks for pans, corner solutions and drawer organisers planned around what you actually store.

Choose Us

Our Cabinet Design and Installation Process in Bluffdale

The same seven stages we run on every Build Right project. On a cabinetry job the first two carry most of the weight, because everything after them is manufacturing to a drawing that was either right or wrong before the wood was cut.

Site Survey

We measure the room properly, checking walls for plumb, floors for level and ceilings for run, because almost none of them are true in a real house. We open a cabinet to look at the carcass rather than the door, check how the existing runs are fixed, and establish whether refacing is realistic before anything is designed.

Design

Layout, door style, finish, storage and hardware planned around how the household actually uses the room. You see visuals and a confirmed budget before a single board is cut. This is the stage where an awkward corner either becomes usable storage or stays dead space for the next twenty years.

Permitting

Cabinetry on its own rarely needs a permit. It needs one when the work moves plumbing or electrical, or when the cabinets form part of a wider remodel that already carries one. Where a permit is required we prepare the documents, submit them and pull it in our own name.

Demolition

Old cabinets removed with worktops and flooring protected, or for a refacing job, doors and drawer fronts taken off while the boxes stay in place. Anything hidden behind a run, old leaks, damaged drywall, redundant pipework, shows itself here and gets dealt with before new cabinetry goes anywhere near it.

Construction

Cabinets built in the shop to the approved drawing, or for refinishing and refacing, doors stripped and sprayed in a controlled environment rather than in your kitchen. Shop time is where the quality is decided. Site time just reveals whether the measuring was right.

Finishes

Cabinets set, levelled, shimmed and scribed to the wall so the run reads straight even where the wall is not. Hardware fitted, doors and drawers aligned, soft-close adjusted. Filler panels, where any are needed, cut to match rather than improvised.

Handover

Final walkthrough, written care instructions for your finish, warranty activation and a scheduled follow-up visit. Doors settle in the first few weeks as the house moves, so the follow-up exists to realign anything that has shifted rather than to tick a box.

Our Work

Recent Cabinet Projects From Our Bluffdale Shop

Cabinetry designed, built and fitted across Bluffdale, Riverton and Draper by the same team each time. Chris, our CEO, has over 18 years in construction, from residential remodels through large-scale hotel builds in the United States, England, Spain and China. More about the team.

Custom Build Around an Awkward Room

A kitchen with a nine-foot ceiling, a chimney breast in the middle of the main run and not one square wall. Built to measure, carried to the ceiling, with the chimney framed into a usable pantry rather than boxed around. No filler panels anywhere a visitor would see one.

Refaced, Not Replaced

Solid maple boxes in good condition behind doors from the late nineties. Doors and fronts replaced in painted shaker, soft-close fitted throughout, veneer matched to the new doors. The homeowner kept the carcasses and spent the difference on the countertops instead.

Two-Tone With White Oak

Painted uppers in a warm off-white over a white oak base and island, chosen as a pair rather than separately. Quarter-sawn boards on the island fronts so the grain reads consistently, and integrated panels on the fridge and dishwasher.

buildright ceo
Chief Executive Officer

Chris

Chris brings over 18 years of construction experience, managing projects from residential remodels through large-scale hotel builds across the United States, England, Spain and China. Hotel work is thousands of identical units fitted to a fixed tolerance, and that is where the habit of measuring the room rather than trusting the drawing comes from.

Flooring Specialist

Jason

Jason specialises in luxury vinyl plank, tile, carpet and floor preparation, with six years in the trade. Cabinets sit on the floor, so a run installed over an unlevel subfloor will never read straight no matter how well it was built. Getting the floor right first is part of getting the cabinets right.

BuildRight Jason
Flooring Expert

Jason

Jason is a skilled flooring professional with 6 years of experience specializing in LVP, tile, carpet, and floor preparation. Known for his attention to detail and excellent customer service, Jason ensures every project is completed with precision and care.

 

FAQS

Common Questions About Custom Kitchen Cabinets

Below are the questions homeowners ask most before committing to cabinetry. If something is not covered here, call 801-419-6696 or read more on our FAQ page.

What is the difference between cabinet refacing, refinishing and painting?
All three keep your existing cabinet boxes and change what you see. Painting coats the doors, drawer fronts and frames in a new colour, hiding the wood grain. Refinishing strips the old finish back and applies new stain or lacquer, keeping the grain visible, so it only works on solid wood. Refacing goes further again: the doors and drawer fronts are replaced entirely and the visible box surfaces are covered with matching veneer, so the style changes rather than just the colour. Cost runs in that order too, from roughly $2,500 for painting to $13,000 for a refaced kitchen.
Custom kitchen cabinets in the Salt Lake Valley typically run $500 to $1,200 per linear foot installed, which puts a standard 25 to 30 foot kitchen between $15,000 and $35,000. Semi-custom cabinets run $150 to $650 per linear foot, or $5,000 to $19,000 for the same kitchen. Refacing the boxes you already have typically costs $4,000 to $13,000, and painting them costs $2,500 to $6,000. Cabinetry is usually the largest single line in a kitchen budget, around 30 to 40 percent of the total. Your written estimate comes from the free in-home survey.
Custom cabinets take 4 to 8 weeks from approved design to installation, and most of that is build time in the shop rather than time on site. Installation itself is usually three to five days for a standard kitchen. Semi-custom runs 4 to 6 weeks, refacing 2 to 4 weeks and painting 1 to 2 weeks. Design and material selection happen before any of those windows start. Because cabinetry is almost always the longest lead item in a kitchen remodel, it gets ordered first and the rest of the schedule is built backwards from its delivery date.
It comes down to the boxes rather than the doors. If the carcasses are solid, square and still firmly attached to the wall, refacing works and saves a substantial amount against replacement. If the boxes are particleboard that has swollen under a leak, if shelves sag, or if the layout itself is the problem, refacing only puts a new face on an old issue. We check all of that at the survey, open a cabinet or two, and say plainly which route makes sense. Changing the layout always means new cabinets, whatever condition the old ones are in.
Semi-custom cabinets are built in standard sizes from a manufacturer’s range, with your choice of door style, finish and some modifications to depth or width. They suit a kitchen keeping its existing footprint. Custom cabinets are built to your exact dimensions in any style and any finish, which matters when a wall is out of square, a ceiling is unusually high, or an awkward corner would otherwise be dead space. The practical test is whether standard sizes would leave filler panels in visible places. If they would, custom usually pays for itself in usable storage.
A shaker cabinet has a five-piece door with a flat recessed centre panel and a plain square frame around it, with no moulding or ornament. The style is roughly two hundred years old and has stayed in continuous use that whole time, which is about as strong an argument against dating as any kitchen style has. It also takes paint and stain equally well, suits traditional and modern kitchens alike, and is easy to clean because there is nowhere for grease to collect. It is the most requested door style we build, by a wide margin.
Yes. Design, build and installation are all handled in-house rather than split between a supplier and a separate fitter. That matters more than it sounds, because most cabinet complaints come from the gap between those two jobs: boxes ordered to the wrong dimensions, doors that will not align because the wall is out of plumb, or filler panels improvised on site. We measure, build and fit, so there is nobody to point at if something does not line up. Installation includes scribing to the wall, levelling, hardware and soft-close adjustment.
Yes. The same shop builds bathroom vanities, basement wet bar cabinetry, laundry room storage, mudroom benches and built-in shelving. Running them through one shop is what keeps the detailing consistent from room to room, which is the clearest marker of a house finished properly rather than piecemeal. It is also usually cheaper, because one set-up and one delivery covers several rooms. Lead times are the same four to eight weeks whichever room the cabinetry is for. Vanity work is covered in more detail on the bathroom remodel page, and basement bar cabinetry on the basement finishing page.

Talk to a Cabinet Installer Near You in Bluffdale

Book a free in-home survey and we will measure the room, look at the boxes you already have and tell you honestly whether to reface, refinish or replace. Written estimate itemised line by line, no pressure to sign on the day. We fit cabinetry across Bluffdale, Salt Lake City and the rest of the valley. Cabinets also run alongside a full home remodel where the whole house is being done at once. Call 801-419-6696.